Duet 3 Mini 5+

129,90 

129,90 

Beschreibung

Duet 3 Mini 5+ Ethernet/ Wifi Controller Board für 3D-Drucker eignet sich für kleine und mittlere Maschinen, die nicht die hohe Leistung des Duet 3 Mainboard 6HC benötigen.

Es besitzt fünf integrierte Treiber (TMC2209) und die üblichen Schnittstellen für Lüfter, Heizelemente, IO´s, LCD, etc.

Das Board bietet die Option einen Single Board Computer (SBC) zur Steuerung zu verwenden

HARDWARE SPECIFICATION
Duet 3 Mini 5+ WiFi Duet 3 Mini 5+ Ethernet
Processor ATSAME54P20A
Processor features 120MHz ARM Cortex M4F, 1Mb flash, 256Kb RAM, hardware floating point (single precision), DMA, 4Kb cache
Networking/Comms 2.4GHz WiFi; USB port; serial port 10BaseT/100BaseTX Ethernet; USB port; serial port.
On-board stepper drivers 5 x TMC2209
Stepper driver features Up to 2.0A peak current (TBC), microstep interpolation from any setting to x256, stall detection, stealthChop2
Heater outputs Bed heater (up to 18A TBC), 2 x extruder heater (up to 5A each)
Thermistor/PT1000 inputs 3, optimised for 100K thermistors and PT1000 sensors
Fan outputs 4 controlled fans of which 2 support 4-wire fans with PWM and tacho wires, voltage selectable between VIN and 12V in 2 banks
Inputs/Outputs 5 on-board I/O connectors plus 2 input-only connectors for endstop, filament monitor, Z probe, servo or PanelDue connection. Inputs are 30V-tolerant. Further expansion via CAN-connected expansion boards.
Endstop or filament monitor inputs See under Inputs/Outputs
Z probe connector See under Inputs/Outputs
Power monitoring VIN voltage monitoring allows for state save on power failure.
SD card interface On-board high speed (22.5Mbytes/sec) SD card socket.
EXPANSION
Support for attached Raspberry Pi or other Single Board Computer (SBC) Yes
External stepper driver support 2 external stepper drivers from stepper driver expansion connector. Multiple expansion via the CAN bus including 1XD external driver boards.
Stepper driver expansion 2 additional TMC2209 stepper drivers using a mini 2+, further expansion via CAN
Heater/thermistor expansion Expansion via CAN using 3HC or toolboard 1XD.
PT100 and thermocouple daughter board support 1 board (2 channels)
Servo support See under Inputs/Outputs. Also one output with 5V signal level for servo, laser or VFD converter (shared control signal with one of the 2-wire fan outputs).
LCD support PanelDue colour touch screen, mini 12864 mono graphics display using ST7567 controller (3.3V signal levels)
LED strip support RGB Neopixel (max. 60 LEDs, external 5V power required)
Other expansion Via I/O ports and CAN bus

 

Wählen Sie zwischen der Ethernet oder Wifi Variante aus

 

Weitere Informationen zur Ausstattung des Boards finden Sie hier:

https://duet3d.dozuki.com/Wiki/Duet_3_Mini_5plus_Hardware_overview

 

 

Weitere Informationen

Gewicht 0,400 kg
Prozessor

32-bit ARM-Prozessor

Schrittmotortreiber

5x TMC 2209

Schnittstellen

externe Wifi-Antenne, Ethernet

Erweiterungen

via CAN Bus z.B. Expansion 3HC, ToolBoards usw.

Schnittstelle

Wifi-EA, Ethernet

Reviews

Customers review
0
0 ratings
1 Star
0%
2 Star
0%
3 Star
0%
4 Star
0%
5 Star
0%
Rate it!

Only logged in customers who have purchased this product may leave a review.

Write A Review
Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.